STM32U575CI产品参数_功能特性_原装供应
概述
STM32U575xx器件属于基于高性能Arm的超低功耗微控制器系列(STM32U5系列)
®
皮质
®
-M33 32位RISC内核。
大脑皮层
®
-M33内核具有单精度FPU(浮点单元),支持所有Arm
®
单精度数据处理指令和所有数据类型。
大脑皮层
®
-M33核心还实现了一整套DSP(数字信号处理)指令和MPU(内存保护单元),增强了应用程序的安全性。
这些器件嵌入高速存储器(高达2 mb的闪存和786 kb的SRAM),用于静态存储器的FSMC(灵活的外部存储器控制器)(用于封装为90引脚及以上的器件),两个Octo-SPI闪存接口(所有封装上至少有一个Quad-SPI)和广泛的增强I/ o和外设连接到三个APB总线,三个AHB总线和32位多AHB总线矩阵。
设备提供符合Arm TBSA (trusted-based security architecture)要求的安全基础
®
。
该器件具有嵌入式闪存和SRAM的几种保护机制:读出保护,写保护,安全和隐藏保护区域。
这些设备嵌入了几个增强安全性的外设:具有抗DPA功能、HASH硬件加速器和真正的随机数生成器。
该设备提供主动篡改检测和保护,防止瞬态和环境扰动攻击,这要归功于几个内部监控,在攻击发生时生成秘密数据擦除。
这些器件提供一个快速14位ADC (2.5 Msps),一个12位ADC (2.5 Msps),两个比较器,两个运算放大器,两个DAC通道,一个内部电压参考缓冲器,一个低功耗RTC,四个32位通用定时器,两个16位PWM定时器专用于电机控制,三个16位通用定时器,两个16位基本定时器和四个16位低功耗定时器。
该器件支持MDF(多功能数字滤波器),具有六个专用于连接外部sigma-delta调制器的滤波器。
这些设备还具有标准和先进的通信接口,如
2
c、3个spi、3个usart、2个UART、1个低功耗UART、2个sai、1个数码相机接口(DCMI)、2个sdmmc、1个FDCAN、1个USB OTG全速、1个USB Type-C /USB Power Delivery控制器、1个通用同步8-/16位PSSI(并行数据输入/输出从接口)。
器件工作温度范围为-40 ~ +85℃(+105℃结)和-40 ~ +125℃(+130℃结),电源电压范围为1.71 ~ 3.6 V。
一套全面的节能模式允许低功耗应用的设计。
支持一些独立电源,如ADC, dac, opamp和比较器的模拟独立电源输入,USB的3.3 V专用电源输入和最多14个I/ o,可以独立供电,低至1.08 V。
这些设备提供8种封装,从48到169个引脚不等。
STM32U575CI符号图
STM32U575CI功能参数
- Includes ST state-of-the-art patented technology
- Ultra-low-power with FlexPowerControl
- 1.71 V to 3.6 V power supply
- –40 °C to +85/125 °C temperature range
- Low-power background autonomous mode (LPBAM): autonomous peripherals with DMA, functional down to Stop 2 mode
- VBAT mode: supply for RTC, 32 x 32-bit backup registers and 2-Kbyte backup SRAM
- 160 nA Shutdown mode (24 wake-up pins)
- 210 nA Standby mode (24 wake-up pins)
- 530 nA Standby mode with RTC
- 1.9 μA Stop 3 mode with 16-Kbyte SRAM
- 4.3 µA Stop 3 mode with full SRAM
- 4.0 µA Stop 2 mode with 16-Kbyte SRAM
- 8.95 µA Stop 2 mode with full SRAM
- 19.5 μA/MHz Run mode @ 3.3 V
- 内核
- Arm® 32-bit Cortex®-M33 CPU with TrustZone®, MPU, DSP, and FPU
- ART Accelerator
- 8-Kbyte instruction cache allowing 0-wait-state execution from flash and external memories: up to 160 MHz, 240 DMIPS
- 4-Kbyte data cache for external memories
- Power management
- Embedded regulator (LDO) and SMPS step-down converter supporting switch on-the-fly and voltage scaling
- Benchmarks
- 1.5 DMIPS/MHz (Drystone 2.1)
- 651 CoreMark® (4.07 CoreMark®/MHz)
- 450 ULPMark™-CP
- 109 ULPMark™-PP
- 51.5 ULPMark™-CM
- 133000 SecureMark™-TLS
- Memories
- 2-Mbyte flash memory with ECC, 2 banks read-while-write, including 512 Kbytes with 100 kcycles
- 786-Kbyte SRAM with ECC OFF or 722-Kbyte SRAM including up to 322-Kbyte SRAM with ECC ON
- External memory interface supporting SRAM, PSRAM, NOR, NAND, and FRAM memories
- 2 Octo-SPI memory interfaces
- 安保
- Arm® TrustZone® and securable I/Os, memories, and peripherals
- Flexible life cycle scheme with RDP and password protected debug
- Root of trust thanks to unique boot entry and secure hide protection area (HDP)
- Secure firmware installation (SFI) thanks to embedded root secure services (RSS)
- Secure firmware upgrade support with TF-M
- HASH hardware accelerator
- True random number generator, NIST SP800-90B compliant
- 96-bit unique ID
- 512-byte OTP (one-time programmable)
- Active tampers
- Clock management
- 4 to 50 MHz crystal oscillator
- 32 kHz crystal oscillator for RTC (LSE)
- Internal 16 MHz factory-trimmed RC (±1%)
- Internal low-power 32 kHz RC (±5%)
- 2 internal multispeed 100 kHz to 48 MHz oscillators, including one autotrimmed by LSE (better than ±0.25% accuracy)
- Internal 48 MHz with clock recovery
- 3 PLLs for system clock, USB, audio, ADC
- General-purpose input/outputs
- Up to 136 fast I/Os with interrupt capability most 5V-tolerant and up to 14 I/Os with independent supply down to 1.08 V
- Up to 17 timers and 2 watchdogs
- 2 16-bit advanced motor-control, 4 32-bit, 5 16-bit, 4 low-power 16-bit (available in Stop mode), 2 SysTick timers and 2 watchdogs
- RTC with hardware calendar and calibration
- Up to 22 communication peripherals
- 1 USB Type-C®/USB power delivery controller
- 1 USB OTG 2.0 full-speed controller
- 2 SAIs (serial audio interface)
- 4 I2C FM+(1 Mbit/s), SMBus/PMBus®
- 6 USARTs (ISO 7816, LIN, IrDA, modem)
- 3 SPIs (5x SPIs with the dual OCTOSPI)
- 1 CAN FD controller
- 2 SDMMC interfaces
- 1 multifunction digital filter (6 filters)+ 1 audio digital filter with sound-activity detection
- Parallel synchronous slave interface
- 16- and 4-channel DMA controllers, functional in Stop mode
- Graphic features
- Chrom-ART Accelerator (DMA2D) for enhanced graphic content creation
- 1 digital camera interface
- Mathematical coprocessor
- CORDIC for trigonometric functions acceleration
- Filter mathematical accelerator (FMAC)
- Up to 22 capacitive sensing channels
- Support touch key, linear, and rotary touch sensors
- Rich analog peripherals (independent supply)
- 14-bit ADC 2.5-Msps with hardware oversampling
- 12-bit ADC 2.5-Msps, with hardware oversampling, autonomous in Stop 2 mode
- 2 12-bit DAC, low-power sample and hold
- 2 operational amplifiers with built-in PGA
- 2 ultra-low-power comparators
- Development support: serial-wire debug (SWD), JTAG, Embedded Trace Macrocell™ (ETM)
- ECOPACK2 compliant packages